The 9 Things Your Parents Taught You About Car Ignition Lock > 자유게시판

Why is My Car Ignition Locked?

There are a variety of reasons your car ignition lock (Suggested Internet page) ignition may be locked. The key might be dirty or may have a damaged wafer inside it. You can fix it by sliding the key into and out of the cylinder several times.

The pins of the lock cylinder can also be stuck. You can use a small tack hammer to gently tap the cylinder to loosen them.

Check the Battery

If your car is in Park or neutral, but won't turn on when the key is inserted into the ignition, there could be a problem with the transmission shifter switch. It is possible to fix the issue by shifting the gear shifter upwards or down to get the vehicle into gear.

If the car still won't turn, the problem could be related to the neutral safety cable or shifter on the transmission. A mechanic or a local auto ignition key replacement locksmith can fix these issues.

The ignition cylinder can also be worn out. Over time, the ignition as well as the key may wear out, causing them to become difficult to remove or insert. A lubricant, like silicon lock lubricant, could solve this issue by allowing the silicon wafers to slide into place.

The key could get clogged with lint in your pockets, as well as adhesive from tape that is used to keep packages in place. This stops the key from sliding into the ignition. To resolve this issue you can try cleaning the keys with a cloth or using a cleaner, like Triflow. You should also make use of a spare key to see if the problem is related to the key or the ignition.

While the key is in the ignition you can tap it using a an hammer that is small. This can cause a slight vibration that could cause enough vibration to loosen the wafers in the ignition and allow them to slide into place. But, be careful not to damage the ignition key or cylinder.

If all of the above methods fail, it's probably time to contact a locksmith or automotive mechanic to examine the issue. The key may be damaged inside the ignition cylinder, or it might be time to replace it altogether. If the problem is with the key the locksmith can create a new key for you. If the problem is related to the ignition cylinder, the car is required to be brought to a repair shop to get it replaced. These issues are generally simple to repair.

Examine the Steering Wheel

A simple problem that can hinder the ignition from turning is the steering wheel being locked. This happens if the driver accidentally engages it as they exit or enter the vehicle. This is usually caused by yanking on the wheel while supporting themselves against it with their hands. It could also happen if someone in the back seat is unable to stop it when they exit the car.

Fortunately it's an easy fix that does not require a trip to an expert locksmith or mechanic. First, check that the gear shift is in either Park or neutral. If it isn't, simply push or pull the shifter until it changes into one of these positions. It's also important to press the brake or turn on the handbrake prior to trying to turn the key.

If the wheel isn't locked taking a look at the steering column will reveal whether the key has been engaged with the lock. This is typically identified by a small "Lock" label on the lower part of the ignition circle. You can easily disengage this by gently moving the key or pulling it with moderate force. It is essential not to use too much force as it could damage the key or cut off a wafer within the lock cylinder.

A spare key may also be used to unengage the lock. This could indicate that the key is worn out and no longer able engage the wafers inside the lock cylinder. If this is the case, a professional at Karl Chevrolet Webster City will be able to design a replacement key.

If the key doesn't engage after spraying the penetrating lubricant it might aid. Apply a small amount around the ignition and keyhole, then gently tap or jiggle it until it starts to work. If this isn't working, you'll likely need to see a specialist at your local auto dealer. They'll be able provide you with a new key and replace the ignition cylinder, if necessary.

Check the Key

If you are unable get your key to turn on the ignition, it's likely that there is something wrong with your key. Try removing any foreign material from the key (lint, adhesive from packing tape, etc). You can also try rubbing alcohol or Goo Gone on the key to see if this aids.

If the pins within the lock do not move properly when you insert your key, it is possible that they are stuck. If you have an extra key that you want to test, put it into the ignition and gently pulling it out. You should be in a position to feel and hear the pins moving inside. If you don't hear or feel any movement, you could lubricate them with graphite powder. You can buy graphite in small tubes that can be applied directly to the keyhole. This will allow the pins to slide into place when you insert the key, and will prevent them from becoming stuck.

It could be that your key has worn out or damaged and isn't able to connect with the pins inside the ignition cylinder. This can cause the cylinder of ignition to not to turn, and prevent you from starting your vehicle. If this is the case you'll need take your vehicle to a locksmith or repair shop for assistance.

If you are able to turn your vehicle with an extra key and you've ruled out issues with the steering wheel or battery It could be that the ignition cylinder is worn out. You can attempt to loosen the lock cylinder by using the blunt end of a screwdriver or the handle of an hammer (not the head). Gently tapping on the cylinder will often free it and allow you to turn your key and start your car. If this does nothing will happen, you'll have to get your lock cylinder changed by an expert mechanic.

Check the Ignition Socket

The ignition socket is the place your key slides in and out of position when it is inserted. It is often covered in debris or as the result of wear and wear and tear. Try spraying some silicon lock lubricant (like WD-40) into the ignition to make things move along.

You can also use a small hammer and tap very gently on the inside of the ignition to try to loosen or reset the pins that are not aligned. Be very careful to not overdo it, or you could cause severe damage to the ignition switch.

Before you do this, ensure that your car's gearbox is set to neutral or park. A lot of newer vehicles come with an option to lock the steering wheel when it is not in neutral or in park. This could prevent the ignition key from being turned.

If you have done all of this but not able to get your key to turn, it is likely that the housing of your ignition cylinder is in need of replacement. It is important to know that different vehicles require different procedures when replacing the ignition cylinder.

Generally, this means taking off the plastic cover that is placed over the steering column and lost ignition key assembly. To remove this, you'll need to first adjust the tilt-wheel to the lowest position and then remove any fasteners that are holding it in place.

Once the cover is removed, you will need to remove the old ignition cylinder out of the steering column. Then, you will need to check the new ignition cylinder you purchased with the one you removed to confirm that they're identical. Once this is done, the new ignition cylinder is able to be installed in the same manner that the previous one was removed.

Sometimes, despite our best efforts, the ignition will become damaged and need to be replaced. It is recommended that if this happens, you contact a Tempe Locksmith. A locksmith will be able to help you select the proper replacement and install it properly to ensure that your vehicle can start again.